Ramsey Electronics SG560 Especificaciones descargar pdf (Pagina 3)

FEATURES

Display: 2 vacuum fluorescent graphical displays, 16x140 pixels

Memories: 100 sequences of 100 registers plus system memories

Sweep Features: Linear, octave, and decade of up to 10,000 points

Scanner Mode: Allows scanning through a sequence of 100 stores

SINAD Meter: Displays reading from -30dB to 0dB of SINAD

Freq. Counter: Measures frequency error to 1 Hz in three counter modes

Battery Meter: Displays charge left in batteries

Reverse Protection: Generator output protected, switches into 100W internal

load and automatically displays power in dBm or watts.

Power Meter: Displays power from +23dBm to +50dBm, ± .5dB

(200mW-100W)

Attenuator Output: -30dB sample port from load for external equipment

RSSI Meter: 80dB of range on receiver side, -40dBm to -120dBm

Warranty: One-year parts and labor with extended Ramsey Technical

Support and dedicated COM3010 user forum access

GENERATE MODE

Frequency: 100kHz to 1.0GHz in 1Hz steps

Freq. Accuracy: ± 0.1ppm standard

RF Output Level: -140dBm to 0dBm in 0.1dBm steps

Level Accuracy: ± 1dB, 500kHz to 1GHz, ±2dB 100kHz to 500kHz

Units: dBm, uV, mV

Leakage: Better than 1uV, 2 turn loop, 1" diameter at 1”

Spurious Harmonics: -30dBc typical

Non-harmonics: -50dBc typical

FM Modulation: ±75kHz max in 0.1Hz steps

FM Bandwidth: 0.1Hz - 75kHz

Accuracy: ± 0.1ppm (inherently tied to reference frequency)

AM Modulation: 0 - 75% in 1% steps to -100dBm, 0-50% to -140dBm

AM Bandwidth: 10Hz - 10kHz

Accuracy: ± 5%

Distortion: Less than 5%

Modulation Internal: 0.1Hz - 3kHz

Modulation External: 0.1Hz - 3kHz digital and analog selectable, auto leveling.

CTS Encode: 0.1Hz to 999.9Hz at ±.75kHz default deviation, variable

from .1Hz to 2kHz deviation

DPL Encode: ±750Hz, all supported codes

RECEIVE MODE

Frequency: 100kHz to 1.0GHz in 10Hz steps

Sensitivity: Less than 2uV below 512MHz

Less than 3uV above 512MHz

FM Demod: 0 - 6kHz, 0 - 4kHz

AM Demod: 0-100%

CTS Decode: In AF frequency count

Frequency Error: 0-1MHz, two methods of bargraph and count

AF Demod output: 1Vp-p for 6kHz deviation

Gates: 0.1 sec, 1 sec

FREQUENCY COUNTER

Frequency Range: 100kHz - 1GHz

Low Band Sensitivity: Less than 10mV under 70MHz, 1Hz and 10Hz

resolutions

High Band Sensitivity: Less than 10mV, 70MHz - 1GHz, 10Hz and 100Hz

resolutions with divide by ten prescaler

IF Frequency: Receiver sensitivity, range limited to bandwidth of current

set receiver frequency ±10kHz, 1Hz, and 10Hz resolutions

AUDIO COUNTER

Frequency Range: 60Hz - 3000Hz

Gates: 10 Sec variable gate for 1 sec quick updates

Sensitivity: 35mV at demod audio, (± 750Hz deviation)

GENERAL

Receiver input: Has diode protection and fused components

Controls: Elastomeric keypad

Dummy Load: 100W 30dB feed-through attenuator with sample port on

rear, 25% duty cycle full power

RS232 Control: Serial interface provides external function control and

automated calibration

Primary power: 100-240VAC, .6A, 50/60Hz; built in Li-Ion battery

Stand: Professional swivel lock handle/stand

Case Color: Mist gray epoxy powder coat

Supplied Accessories: 110VAC EIA cord, BNC-BNC test cable, whip antenna, one

BP3010 Li-Ion battery

Dimensions: 6” H x 11.9375” W x 14.75” D (152.4mm H x 303.31mm

W x 374.65mm D)

Weight: 14 lbs (6.5kg)

HAND HELD SCOPE OPTION

Max Sample Rate: 10MHz (2MHz single shot)

Max Input Bandwidth: 2MHz (-3dB at 50mV, 1V & 20V/Div x 1 setting)

Input Impedance: 1M ohm, 20pf standard scope probes

Input Coupling: DC, AC, and ground (zero reference)

Vert Resolution: 8 bit, ±1 bit linearity

Trigger Modes: Run, normal, once, roll mode for 1s/div and

slower timebase

LCD Graphics: 64 x 128 pixel, white backlit

Signal Storage: 256 samples with 2 memories, max 125 visible

samples, 256 using X shift

dBm Measurement: -73dB to +40dB, ±0.5dB accuracy

(0dBm=0.775V at 600 ohm)

dBV Measurement: -75dB to +38dB, ±0.5dB accuracy

(0dBV=1V)

True RMS Measurement: .1mV to 80V, ±2.5% accuracy

P/P AC Range: 0.1mV to 160V, ±2.0% accuracy

Timebase Ranges: 0.2us to 1hr/div, 32 steps

Input Sensitivity Range: 5mV to 20V/div at time 1, 50mV to 200V/div

at times 10, 12 steps

Probe Calibration Output: 2KHz/5Vpp approx

Power Requirement: 9V, 500mA adapter provided

Batteries: (not included) 5 AA Alkaline batteries

or 5 AA NiMH rechargable batteries

Battery Life: Up to 20 hours with AA Alkaline

Operating Temperature: 0° to 50° C (32° to 122° F)

Dimensions: 4.13” x 7.95” x 1.38” (105mm x 220mm x 35mm)

Weight: 14 oz (395g) less batteries

Accessories Provided: Foam lined carrying case, COM3010 interface cable,

standard scope probes, AC power supply, user’s manual

Optional Accessories: BP3010 Additional Li-Ion battery pack (max 3)

CC3010 Black padded Cordura carrying case

DETAILED SPECIFICATIONS

COM3010 Full Duplex Communications Service Monitor, 100kHz - 1.0GHz, with One 1-Hour Li-Ion Battery Pack $3995.00

BP3010 Additional Li-Ion Battery Pack, Extends Battery Operation By One Hour (Maximum 3 Packs) $59.95

CC3010 Matching Black Padded Cordura Carrying Case With Strap $129.95

1 2 3 4 5 6 7 8 ... 15 16

Comentarios a estos manuales

Sin comentarios

Ramsey Electronics SG560 Especificaciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Generadores De Poder Ramsey Electronics SG560